Making Raised Panel Doors With A Router

🔥+ Making Raised Panel Doors With A Router 06 Aug 2020 Max Fulbright Designs- Max Fulbright specializes in craftsman, cottage, lake and mountain house designs with rustic materials and craftsman details.

Making Raised Panel Doors With A Router This blanket chest is the ideal project to showcase this technique. Link Type: free plans

Glass Cabinet Door Designs Skip to main content
Ana White
Submitted by Ana White on Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Fri, 04/23/2010 - 20:27
Difficulty
Beginner
|

A touch of contemporary to your outdoor space. This easy to build bench features a slatted top. Use indoors and out, as dining seating or just a bench to rest on outdoors.

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Somebody''s gonna whisper, she''s from.  She thinks she lives in Hollywood now.  And they are so right.  Despite plans for ice fishing this weekend, I''ve got the table, and now it''s Wood Slat Long Bench, loving the modern simplicity of this style.  I especially love simple clean lines outdoors because you are contrasting against the natural organic shapes of the outdoors.

If you are intimidated by the size of the table, starting with the bench is a good idea.  Not only will you have an opportunity to make mistakes and learn from them, the investment (time and moneywise) is considerably less.  Also, the bench could serve a variety of other purposes besides as a dining area seating surface.  Think holding planters, elevating plants for sunshine, or just a simple reading spot.

Preparation

Shopping List

Shopping List

4 – 1×3 Boards
4 – 1×4 Boards
2″ Screws
1 1/4″ Screws
Wood Glue
Wood Filler or Paintable Silicone Sealant

for 1 last update 2020/08/06 ToolsTools

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Measuring Tape
Square
Drill
Sander
Saw

Common Materials
120 grit sandpaper
primer
wood conditioner
paint
paint brush
Cut List

Cut List

2 – 1×3 @ 49 1/4″ (Seat Supports)
2 – 1×3 @ 13″ (End Aprons)
2 – 1×3 @ 50 3/4″ (Side Aprons)
14 – 1×4 @ 11″ (Seat Slats)
2 – 1×4 @ 52 1/4″ (Seat Sides)
4 – 1×4 @ 17 1/4″ (Legs)

Tools
General Instructions

General Instructions. It is a good idea to sand and finish your boards (paint or stain) before constructing to seal all edges. Work on a clean levels surface. Mark out your joints before fastening joints. Predrill and countersink your screws before attaching. Use glue unless otherwise specified. Check for square after each step. And please work safe and smart, using proper safety equipment.

Instructions

Step 1

Build the Frame. Begin by fastening the blue supports to the yellow ends using 2″ screws and glue. Then fasten the green aprons to the yellow aprons as shown above, using 2″ screws and glue. Square up your frame by taking a diagonal measurement, and adjusting the square until both measurements are equal.

Step 2

Bench Slats. Mark the slat boards 1″ from the ends on both ends. Also mark two of the boards 3/4″ in on the outer edge. These are your outer boards. Line these boards up on the ends, overhang of 3/4″ as shown above and screw to side aprons and supports. Fasten the remaining slats to the top, as shown above, leaving a 1/4″ gap between the boards. Use the 1″ marks to line up with the outer edge of the support underneath. It may help you to use the board from step 3 as a guide when lining up your slats.

Step 3

Sides of Bench Top. Mark the bench top boards as shown above, 1 3/4″ in from the sides, 3/4″ from for 1 last update 2020/08/06 the ends. Use 2″ screws to fasten to the side and end aprons.Sides of Bench Top. Mark the bench top boards as shown above, 1 3/4″ in from the sides, 3/4″ from the ends. Use 2″ screws to fasten to the side and end aprons.

Step 4

Legs. Use the 1 1/4″ screws to fasten the legs to the aprons, as shown above. Then fasten from the seat sides top into the tops of the legs with 2″ screws and glue.

Help Improve This Plan

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for We apologize if there was an error in this plan. Please help us out and report any errors here.

Comments

Viola (not for 1 last update 2020/08/06 verified)Viola (not verified)

Sat, 04/24/2010 - 08:06

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Thank you Ana for the plans.

Thank you Ana for the plans. I so want o build this.
Congrats on the domain.

handcrafted fu… (not verified)

Sat, 04/24/2010 - 08:30

Very nicely explained with an

Very nicely explained with an easy design...it is going to be very easy for the freshers specially to make as per the design with these guidance and help.

furniture

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Kai (not verified)

the 1 last update 2020/08/06 Sat, 04/24/2010 - 09:52Sat, 04/24/2010 - 09:52

Thank you so much for posting

Thank you so much for posting this! I was so hoping you would do the bench as well! I can''m looking forward to putting your '' to good use!

Cristy (not verified)

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for Sun, 04/25/2010 - 05:18

You are fantastic! Thanks!

You are fantastic! Thanks! I can't wait to make a couple of these benches to go next to my firepit.

dana (not verified)

the 1 last update 2020/08/06 Mon, 04/26/2010 - 17:28Mon, 04/26/2010 - 17:28

Making Raised Panel Doors With A Routerhow to Making Raised Panel Doors With A Router for This is all way too cool.Just

This is all the 1 last update 2020/08/06 way too cool.
Just found your blog. So glad I did!
- dana
www.dana-made-it.comThis is all way too cool.
Just found your blog. So glad I did!
- dana
www.dana-made-it.com

Deb (not verified)

Fri, 04/30/2010 - 09:36

We just had the concrete

We just had the concrete patio poured at our house and I was looking for some type of patio furniture that would be study and not cost a fortune. Thanks for the plans, I am going to build this tomorrow!

you give GREAT step by step information that doesn’t need any questions asked,

THANK YOU!
-Debbie

Back